NCR 6001-0012-8801 Скачать руководство пользователя страница 35

Страница: 35 / 80

Ovation Installation

Ovation Installation

New Door Preparation

Drill PPU Flex Cable and Attachment Stud Holes to the new Dis-
penser Door (497-0513464)

Note:

Read all instructions prior to beginning this section.

Warning:

The following steps must be completed prior to beginning the installation

process at the pump dispenser. Power tools like drills cannot be used near the
pump dispensers. Power tools cannot be used in a hazardous location within a
dispenser site. Remove the doors to a safe location prior to drilling or use
pneumatic tools.

1. Drill the PPU Flex Cable hole.

Caution:

use care when drilling to align the holes and center them as indicated.

a. Identify the amount and location of PPUs according to the removed PPU plate

from the old dispenser door.

b. Begin drilling the PPU Flex Cable hole on the indention corresponding to the

correct PPU location using a 3/8 drill bit. Plunge the hole to clean up the edges.

Caution:

Verify the PPU positions prior to drilling.

Содержание 6001-0012-8801

















































































Результаты поиска

Содержание 6001-0012-8801

Отзывы:

Похожие инструкции для 6001-0012-8801

Бренды по названию

Популярные бренды

NCR 6001-0012-8801, Руководство по установке

Результаты поиска

Содержание 6001-0012-8801

Отзывы:

Похожие инструкции для 6001-0012-8801

Бренды по названию

Популярные бренды