NCR 5965 Скачать руководство пользователя страница 2

The product described in this book is a licensed product of NCR Corporation. 

NCR is a registered trademark of NCR Corporation. 

NCR RealPOS is either a registered trademark or a trademark of NCR Corporation in the United States and/or other countries. 

It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become available. 
NCR, therefore, reserves the right to change specifications without prior notice. 

All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, 
photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for 
information that is applicable and current. 

To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value of this book. 

Address correspondence to: 

Manger, Information Products  
NCR Corporation 
2651 Satellite Blvd. 
Duluth, GA  30096 

Or send feedback: 

http://www.info.ncr.com/eFeedback.cfm

 

Copyright © 2008 
By NCR Corporation 
Dayton, Ohio U.S.A. 
All Rights Reserved

Содержание 5965




























































































Отзывы: