manualshive.com logo in svg

NCE Switch-It, Быстрое руководство, Страница: 1 / 6

Поделиться
Скачать
NCE Switch-It Скачать руководство пользователя страница 1

Switch-It

Accessory Decoder

FOR STALL MOTOR SWITCH MACHINES ONLY

NOT FOR USE WITH TWIN COIL SWITCH MACHINES

Dimensions:  2.1" x 1.3"   (54 x 33 mm)

Decoder revision C 

$19.95

Now with EASIER PROGRAMMING!

This is an accessory (switch machine) decoder

‚

Control for two Tortoise

TM

 switch machines

‚

Switch-It remembers the position of switch during power outages

‚

Switch-It supports the full range of DCC accessory addresses (1-2044)

‚

Easy address programming, no need to connect it to programming track

‚

Each switch machine can have its own completely different address

‚

Simple hook up, 2 wires to the track, 2 wires to each switch machine

‚

Includes optional connections for "local" control push buttons

‚

Also operates on non-DCC 

layouts

Every attempt has been made to ensure this decoder complies with all

applicable NMRA Standards and Recommended Practices 

This book, schematics and artwork copyright 1998-2007 

NCE Corporation   899 Ridge Road   Webster, NY  14580

Switch-It is a trademark of NCE Corporation

            Last revised:  15 March 2007                                                                              

Содержание Switch-It







Отзывы:

Нет отзывов