6
AUTOMATIC STOP FEATURE
When the cassette deck is operating in play or record mode and the end of the tape is reached, the unit
automatically shuts itself off and returns all buttons to the off position.
TYPES OF CASSETTE
Use only good quality cassettes (IEC TYPE 1) for making recordings. May be used to replay other types
of cassette but is unable to make proper recording on these more specialized tapes.
The use of C120 cassettes is NOT recommended in this machine.
PROTECTING RECORDING
Normally, anything recorded on the tape is automatically erased when new recording is made. It is
possible to protect your recording from accidental erasure by removing the tabs found on the rear of the
cassette.
When the cassette is held with the recorded side upper-most and exposed tape facing the front, the
protective tab will be found on the left rear of the cassette.
All pre-recorded cassette are protected in this way to prevent accidental erasure of the commercial
recording. “Protected” cassette will prevent the record button from being operated. If at any time you
attempt to record and find that this button will not depress, never force the mechanism or it may be
damaged. Check that a cassette has been loaded and that tab has not been removed. Recording on a
cassette from which the tabs have been removed can be done by covering the tab openings with a piece
of adhesive tape.
CARE OF CASSETTE MECHANISM
Gently clean the tape head and pinch wheel/capstan assemblies after every 10 hours of using the unit.
A range of cassette care products are available.
The erase head and record/play head and the surface of the pinch roller are delicate and must not be
touched with metal objects such as screwdrivers. You may find it easier to clean the assembly by
pressing the PLAY button to bright head and pinch roller into view. Be sure to press the STOP button
after cleaning the mechanism.
Damage to the pinch wheel can occur if the unit is left in PLAY mode with the power switch off. Under
no circumstances should you attempt to lubricate any part of the machine.
RECORDING FROM THE RADIO
1.
Load a blank tape into the tape compartment and close the door.
2.
Press the STANDBY/FUNCTION button on unit or the FUNCTION key on remote to AM or FM
mode. Tune to required station by rotating the TUNING KNOB.
3.
Press RECORD key to begin recording. The RECORD key and PLAY key go down simultaneously.
4.
Press STOP/EJ. key to end recording.
5.
To hear what you recorded, follow instructions in PLAYING A CASSETTE TAPE.
NOTE:
PAUSE FOR A MOMENT - Using the PAUSE key on the cassette deck instead of the
STOP/EJ. key to momentarily interrupt recording gives you a much clear recording.
RADIO RECORDING TIPS
To temporarily pause the recording, press PAUSE key on the cassette deck. Press PAUSE key again to
resume recording.
7
CD/MP3/USB RECORDING
A.
Install a blank tape into cassette compartment.
B.
Press the STANDBY/FUNCTION button on unit or the FUNCTION key on remote to CD or USB
mode. Load a disc into the disc compartment or insert a USB bar into the USB slot, start playback by
pressing the CD PLAY/PAUSE button.
C.
Press the RECORD BUTTON and PLAY BUTTON simultaneously to start recording. Press the
STOP/EJ BUTTON lightly to end recording, or the unit will stop recording automatically while the
tape reaches its end.
D.
To listen to the recording, press FUNCTION button to select “TAP” playing mode, then start tape
playback.
USING THE CD/MP3
Discs for Playback
This system can playback all digital audio CD, MP3 finalized digital audio CD-Recordable (CD-R) discs,
finalized digital audio CD-Rewritable (CD-RW) discs and CD-DA format digital audio
CD/CD-R/CD-RW discs.
LOADING A DISC
1.
Press the STANDBY/FUNCTION button on unit or the FUNCTION key on remote to CD mode.
2.
Open the CD door. “
OP
” will be shown on the display.
3.
Place an audio CD/MP3 into the tray with the label side facing up.
4.
Close the CD door. The total number of tracks and the disc type will appear on the display after
several seconds.
5.
To remove the CD, press CD door PUSH OPEN/CLOSE to open CD compartment lid, grasp the CD
by its edges, and carefully take it out.
Note:
To ensure good system performance, wait until the disc tray completely reads the disc before
proceeding.
If no disc loaded into the compartment, or the disc is place upside down or unreadable, the display
will show
no
.
PLAYING A DISC
1.
The playback starts from track 1 automatically when reading the disc.
To pause playback, press PLAY/PAUSE button on unit or on remote. The current playing time will
flash on the display.
To resume playback, press PLAY/PAUSE button on unit or on remote again.
2.
To stop playback, press STOP button on unit or on remote, the total number of tracks.
SELECTING A DESIRED TRACK/PASSAGE
To select a desired track
Press the NEXT/TUN.+ or BACK/TUN.- button on unit or the TUN./SKIP SEARCH
FORWARD/BACWARD on remote respectively in stop mode or during playing until the desired track
appears on the display. Press the PLAY/PAUSE button on unit or on remote to start play.
To search for a particular passage during playback (track scanning at high speed)
Press and hold the NEXT/TUN.+ or BACK/TUN.- button on unit or the TUN./SKIP SEARCH
FORWARD/BACWARD on remote to scan the current playing track at high speed until desired point
(passage) appears, then release the button for normal playback mode. Playback will start again from this
point.
Содержание NPB-259
Страница 1: ......
