background image

 

 Version  14.03.2022 

HW 16-(V65) 

VL1-NG4-HU 

P

a

g

e

6

 

 
1.4.

 

Dip-switch settings 

 
Some settings must be selected by the dip-switches on the  
video-interface. Dip position down is ON and position up is OFF. 

See following chapters for detailed information. 
 
 
1.4.1.

 

Enabling the interface’s video inputs (dip 2-3) 

 

Only the enabled video inputs can be accessed when switching through the interface’s video 
sources.  It is recommended to enable only the required inputs for the disabled will be 
skipped when switching through the video-interfaces inputs. 
 
1.4.2.

 

Rear-view camera setting (dip 5) 

 

If set to OFF, the interface switches to factory LVDS picture while the reverse gear is engaged 
to display factory rear-view camera or factory optical park system picture. 
If set to ON, the interface witches to its rear-view camera input CAM while the reverse gear 
is engaged. 
 
1.4.3.

 

Monitor selection (dip 7-8) 

 
Dip 7 and 8 are for monitor-specific video settings which cannot be predicted as even within 
the same head-unit version, the monitor specifications may vary. It is necessary to try all 
possible combinations (both OFF, both ON, 7 OFF and 8 ON, 7 ON and 8 OFF) - while a 
working video source is connected to the chosen input of the interface - to see which 
combination gives the best picture quality and size (some may give no picture). It is possible 
to first hot plug through the dip combinations, but if you do not experience any change of 
picture after trying all 4 options, retry and disconnected the 6pin power plug of the video-
box between every change of the dip setting. 
 
Dip1, 4 and 6 are out of function and have to be set to OFF 

 

Dip 

Function 

ON (down) 

OFF (up) 

No function 

 

set to OFF 

CVBS AV1-input 

enabled 

disabled 

CVBS AV2-input 

enabled 

disabled 

No function 

 

set to OFF 

Rear-view cam type 

after-market 

factory or none 

No function 

set to OFF 

Monitor         

selection 

Try all 4 possible combinations of dip 7 and 8 to find the 

best picture (quality and size) 

Содержание VL1-NG4-HU



















Отзывы: