background image

 

Operator Manual                                                                                                            Chapter3. For the beginning operator   

 

 

                                                                                           

©  

Nautilus Hyosung, Inc. 

All Rights Reserved.                                                      3-11

 

Electronic Lock 

 

 

 Opening the locks   

1. Enter valid six (6) digit combination. (Factory set to 1-2-3-4-5-6) 
2. The lock will confirm a valid combination entry with a double signal. 
3. Within four (4) seconds, turn the keypad to the open position (clock-wise) 

if using a dead bolt style lock, or turn the handle to the open position if using a swing bolt 
style lock. 

4. Pull door open. 

 

Invalid Combination Entry   

- Lock will signal three (3) times. 

 

WRONG TRY PENALTY 

▪ Entry of four (4) consecutive invalid combinations             

starts a five (5) minute delay period. 

- LED flashes red at ten (10) second intervals. 

 

Audio and Visual Signal       

▪ Double signal - two (2) LED flashes and two (2)     

beeps - indicates entry is valid or accepted. 

▪ Triple signal - three (3) LED flashes and three (3) beeps - indicates invalid or not accepted. 

 

 Changing your combination 
▪ ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN 

1. Enter “1-2-3-4-5-6” and hold down the last digit until unit double signals. 
2. Enter “0” one time. 
3. Enter your NEW six (6) digit combination two times. 
4. If a mistake is made wait thirty (30) seconds and repeat steps 1 - 3. 
5. Test lock operation several times before closing the door. 

 

<

CAUTION

When  selecting  a  combination  do  not  use  birthday  or  other  predictable  data  that  could  give 
correlation between the user and combination. Keep the combination secret. 

 

▪ Valid Combination Entry - Double signal after valid six (6) digit combination is entered. 
▪ Invalid Combination Entry - Triple signal indicates the old combination is still valid. 

 

 Battery Low Warning 

Repeated LED flashing and beeping during an opening indicates that the battery is low and 
needs immediate replacement. 
Use only alkaline batteries (Example: Duracell ™or Eveready™ alkaline batteries) 
▪  Use  one  (1)  9-Volt  alkaline  battery  in  the  Small  Battery  Box  or  six  (6)  “C”  cell  alkaline 

batteries in the Large Battery Box. 

It is recommended that batteries be replaced at least once a year. 

 

 
If the battery is depleted and will not allow the lock to open: 

Содержание MONiMAX7600DA







































































































Отзывы: