2/4
w w w. n a u t i ch a r g e r. co m
WARNING!
Operation of the inverter without a
proper ground connection may
result in an electrical safety hazard.
WARNING!
Shock Hazard. Before proceeding.
Further, ensure that the Inverter is
NOT connected to any Batteries,
and that all wiring is disconnected
from any electrical Sources.
Do not connect the output
Terminals of the Inverter to an
incoming AC sources. The inverter
will be damaged permanently, not
covered by our warranty.
WARNING!
Make sure all the DC connections
are tight (torque to 9-10 ft-lbs,11.7-
13Nm). Loose connections will
overheat and could result in a
potential hazard.
CAUTION!
Reverse polarity connection will
blow a fuse in Inverter and may
permanently damage the inverter.
Damage caused by reverse polarity
connection is not covered by our
warranty.
WARNING !
You may observe a spark when you
make this connection since current
may flow to charge capacitors in
the power inverter.
Do not make this connection in the
presence of flammable fumes,
explosion or fire may result.
WARNING!
Do not open or disassemble
Inverter, attempting to service the
unit yourself may result in a risk of
electrical shock or fire.
Installation:
•
Where to install
The power inverter should be installed in a location that meets the
following requirements:
•
Dry
– Do not allow water to drip or splash on the inverter.
•
Cool
– Ambient air temperature should be between 0 degrees
and 40 degrees C. Do not place the inverter in direct sunlight if
avoidable.
•
Safe
–Do not install in a battery compartment or other areas
where flammable fumes may exist, such as fuel storage are as or
engine compartments.
•
Ventilated
– Allow at least one inch of clearance around the
inverter for air flow. Ensure the ventilation openings on the rear
and bottom of the unit are not obstructed.
•
Dust-free
–Do not install the Inverter in a dusty environment
where either dust, wood particles or other filings/shavings are
present. These can pulled into the unit when the cooling fan is
operating.
•
Close to battery/batteries
– Avoid excessive cable lengths but
do not install the Inverter in the same compartment as batteries.
Use the recommended wire lengths and sizes. Also do not mount
the Inverter where it will be exposed to the gases produced by the
battery. These gases are very corrosive and prolonged exposure
will damage the Inverter.
AC safety Grounding
During the AC wiring installation, AC input and output ground wires are
connected to the inverter. The AC input ground wire must connect to
the incoming ground from your AC utility source.
The AC output ground wire should go to the grounding point for
your loads ( for example, a distribution panel ground bus ).
The installation of the inverter
must comply with your
countries electrical current
regulations of the appliance
CAU TIO N
1. Please do not use the inverter if the DC input source is not 12Vdc
for the 12V inverters or 24Vdc for the 24V inverters, and appliances
are not 230Vac (220-240 Vac).
2. When you stop using it, please pull out the plug. Because of the high
temperature of the metal part, do not touch the plug by hand or place
it near flammable and easy-melting materials.
3. Under Voltage Protection system will automatically switch off the
inverter if the input voltage is too low. Please start the engine to
charge the battery, or stop using it.
4. If the consumption power is over inverter power rate itself, when
switching on appliances, a protection system will indicate the
overload.
5. Due to the difference of the waveform, buzzing and lines on audio
and video equipment might appear.
6. How to select cigar plug or alligator clip for use:
(1) Cigar-Lighter: use with electric equipment below 150 Watt output.
(2) Alligator clips: use with electric equipment over 150 Watt output.
7. We recommend you should use pure sine wave inverter on very
sensitive test equipment.
8. Do not use the inverter if the power cable or plug is damaged or
loose.
9. Do not put any object into the inverter: it may cause fire, electric
＋
－
