background image

 

 

 

1.

 

All NAUTICAM Products are warranted against any material and manufacturing 
defects for one year from the date of purchase for consumer use. 

2.

 

NAUTICAM accepts no liability for any damage to and defects in the housing 
caused by improper use and/or poor maintenance; it is the responsibility of the 
owner to carefully follow the instructions in this manual. 

3.

 

NAUTICAM does not hold responsibility for damage, of any nature, to any 
equipment used with and/or placed within the housing.  

4.

 

NAUTICAM accepts no liability for any loss of captured images or the inability 
to capture images even if it is due to the malfunctioning or leakage of the 
housing. 

5.

 

This warranty only applies to products purchased from authorised NAUTICAM 
dealers and does not extend beyond the original retail purchaser. 

6.

 

Unauthorised modifications and/or repairs of the housing will automatically 
invalidate this warranty. 

7.

 

To return products for service, please contact our regional distributor, 
normally you would need to notify them by email first and ship them the 
product by registered mail, along with your contact details and a brief 
description of the defect. 

 

 

 

Содержание NA-60D
























Отзывы: