
XR12 Troubleshooting Manual
Responding to alarms
Issue 3.0 2009-07-28
Page 1-19
1. If E19 is between pins 2 and 3, verify the dc voltage between TB2-6 and ground on the
remote interface PWB is approximately 24 V. This signifies there is no external PDM inhibit
command.
2. If E19 is between pins 1 and 2, verify the dc voltage between TB1-3 and TB2-6 on the
remote interface PWB is 0 V. This signifies there is no external PDM inhibit command.
are met, suspect the remote interface PWB or the
control/display PWB.
Int. serial fail
This alarm indicates that there is no communication with the remote interface PWB. This alarm is
triggered if two seconds go by without acknowledgement from the remote interface PWB of the
control/display PWB's request for information. (The control/display PWB requests updates from
the remote interface PWB every 200 ms).
1. Check the cable between connector P1 (mates with J1 of the control/display PWB) and
connector P15 (mates with J13 of the remote interface PWB). If the cable and connections
are intact, suspect a problem with the control/dispaly PWB or remote interface PWB.
Mod. protection
This fail is reported from the remote interface PWB.
The exciter monitors a sample of the RF output and conditions the modulator outputs if the RF drive
current becomes great enough to damage the modulators. A
Mod Protection
alarm may occur from
overdriving the transmitter (high output power, high modulation depth, or very low modulating
frequency), a fault in the control/display PWB's alarm circuitry, or a fault in the remote interface
PWB's circuitry. Troubleshoot a
Mod Protection
alarm as follows:
1. Examine the operating conditions under which the alarm occurred. A
Mod Protection
alarm may be initiated if the transmitter is running at rated power with high modulation at a
low modulating frequency. If these conditions were present at the time of the alarm, adjust
the modulating audio low frequency roll off to 30 Hz.
2. Use an oscilloscope to view TP6 on the interphase PDM driver PWB. If the transmitter is
operating at rated power and the audio is clipped (see
of the
XR12
Operating and Maintenance Manual
.
Содержание XR12
