GV60 TROUBLESHOOTING MANUAL
RESPONDING TO ALARMS
PAGE 4.1.58
VERSION 1.0 2018-01-01
Reject Load or Reject Load/Splitter Interface Assembly
Replacement
NOTE
: Replacement instructions listed below, describe assemblies in Cabinet A. Assemblies in Cabinet
B have A1xx designations (ie. RF Drive Splitter A27 for Cabinet A and A127 for Cabinet B).
Using
as a guide, replace one of the four reject load assemblies or one of
the two reject load/splitter interface assemblies as detailed in this section. Identify the affected reject
load, possibly named in an alarm reference and then replace it, as follows:
RF Drive Splitter A27/A127 - accepts two of the six 5 kW reject power inputs (RF power modules 1-
2 and 3-4) (see
“5 kW or 10 kW Reject Load Replacement” on page 4.1.58
)
4-Input Reject Load A29/A129 - accepts four of the six 5 kW reject power inputs (RF power
modules 5-6, 7-8, 9-10 and 11-12) (see
“5 kW or 10 kW Reject Load Replacement” on page 4.1.58
)
4-Input Reject Load A31/A131 - accepts the three 10 kW reject power inputs (RF power modules 1-
4, 5-8 and 9-12) (see
“5 kW or 10 kW Reject Load Replacement” on page 4.1.58
2-Input Reject Load A13/A113 - accepts the 20 kW reject load power input (RF power modules 1-8)
and the final (30 kW) reject load input (RF power modules 1-12) (see
)
Reject Load/Splitter Interface Assembly (A28 and A30/A128 and A130) - see
Interface Assembly Replacement” on page 4.1.61
5 kW or 10 kW Reject Load Replacement
.
NOTE
: 4-input reject load assembly A29 contains four of the six 5 kW reject load circuits. The remaining
two 5 kW reject load circuits are part of 20 kW RF drive splitter assembly A27. 4-input reject load A31
contains the 10 kW reject load circuits.
1.
Open the appropriate front door and remove the appropriate upper, rear panel.
2.
From the front of the transmitter:
Gain access to the suspect reject load [A27 or A29 (5 kW) or A31 (10 kW) by removing the fan
cover (four M5 screws at the top and two hooks in the bottom) and lifting the panel out.
Temporarily remove the reject load/splitter interface assembly (see
Interface Assembly Replacement” on page 4.1.61
Remove the four M4 screws that secure the reject load assembly to the transmitter.
Содержание GV60
