manualshive.com logo in svg

Nautel GV20, Руководство по установке, Страница: 20 / 66

Поделиться
Скачать
Nautel GV20 Скачать руководство пользователя страница 20

GV20/GV15 INSTALLATION MANUAL

INSTALLING OPTIONS

PAGE 2.3.2

VERSION 5.0  2021-03-01

Upgrading to Dual Exciter

The GV20/GV15 is factory configured with a single exciter (A5). You can upgrade your transmitter with 
a second exciter (exciter B, A6). which provides additional redundancy.

1.

Turn off (disable or lock out, as applicable) the main ac power for the transmitter.

2.

Obtain “QG14002* - GV Dual Exciter Upgrade Quick Guide” (see 

Figure 2.3.1

) that was provided

with the Dual Exciter Upgrade Kit and complete its outlined procedure.

Figure 2.3.1: Dual Exciter Upgrade Quick Guide (QG14002*)

3.

If you are performing this upgrade in conjunction with the GV20/GV15’s initial installation, leave
the front and rear panels off to allow further installation. If you are performing this upgrade after
initial installation has already been completed, re-install the front and rear panels.

SHOWN FOR REFERENCE ONLY

Содержание GV20



































































Отзывы:

Нет отзывов