Nautel Exporter Plus Скачать руководство пользователя страница 81

Страница: 81 / 186

Exporter Plus Technical Instruction Manual

Operating

Issue 1.0 2020-05-05

Page 8-11

Use the up and down buttons to highlight the desired mode. Press the accept or cancel button

to enter the Save/Cancel screen (see

Figure 8.4 on page 8-5

). Save or cancel as desired.

Figure 8.11: Operating Mode Editing Screen

Clearing faults

When you select

Clear Faults

from the

SYSTEM

menu (see

Figure 8.12

) you can clear faults that

are displayed, but no longer active (e.g., GPS PLL Error).

Figure 8.12: Clear Faults Screen

To clear faults, press the checkmark (accept) button to ente r the editing screen shown in

Figure 8.13

Figure 8.13: Clear Faults Editing Screen

Use the up and down buttons to highlight

Yes

. Press the accept or cancel button to enter

the Save/Cancel screen (see

Figure 8.4 on page 8-5

). Save or cancel as desired. Selecting

Yes

clears any displayed alarms that are no longer active.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 81 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: