manualshive.com logo in svg

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 44 / 186

Поделиться
Скачать
Nautel Exporter Plus Скачать руководство пользователя страница 44

Exporter Plus Technical Instruction Manual

Quick setup procedure

Page 6-6

Issue 1.0  2020-05-05

Figure 6.4: Network Configuration

1. Enter the UI’s 

Edit Settings - Network Config 

page (see 

Figure 6.4

).

2. Select the appropriate item from the 

NETWORK CONFIG

 list. If necessary, configure the 

mode, IP address and netmask for one or both Ethernet ports (0 and 1), as applicable, 

and the default gateway address. If changes are made, save each setting.

3. Set 

Enable IP Forward

 to 

Yes

 if both Ethernet ports are used.

Factory default settings

Eth 0 Mode = Static
Eth 0 IP Address = 10.10.10.10
Eth 0 Netmask = 255.255.255.0
Eth 1 Mode = Dynamic
Eth 1 IP Address = N/A (dynamic)
Eth 1 Netmask = 255.255.255.0
Default Gateway = 0.0.0.0
DNS Server IP = 0.0.0.0
Enable IP Forward = Yes

NOTES:

Eth 0 is typically used to connect to the Exgine or Importer.
Eth 1 can optionally be used to connect tthe Exporter Plus to a customer network.

To access external networks, set the Default Gateway IP for the IP of the customer supplied router.

DNS Server IP is used only for Static IP mode. If DHCP (Dynamic) is selected for either interface, the 
DHCP will provide the DNS IP.

Содержание Exporter Plus



























































































































































































Отзывы:

Нет отзывов