manualshive.com logo in svg

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 23 / 186

Поделиться
Скачать
Nautel Exporter Plus Скачать руководство пользователя страница 23

Exporter Plus Technical Instruction Manual

Pre-installation tasks

Issue 1.0  2020-05-05

Page 2-1

Section 2:  

Pre-installation tasks

This section provides a list of tasks that you must perform prior to delivery and installation of 

the Exporter Plus. 

Preparing for installation

To prepare for installation of an Exporter Plus, perform the following tasks:

1. Select a location for the Exporter Plus in the studio or the transmitter site. For detailed 

information, see 

“Selecting a location for the Exporter Plus” on page 2-2

.

2. Prepare the network (LAN) connection between the Exporter Plus and the exciter. 

Consider the Exporter Plus's location and the amount of other networked equipment 

at the transmitter site.

3. Consult your network manager for IP address information for the Exporter Plus, 

exciter (Exgine), and gateway.

4. Order any accessories or optional equipment that you may need. See 

Section 3, “Parts 

and tools” on page 3-1

.

5. Train your station technicians and operators on the use of the Exporter Plus. For a list 

of available technical and user documents, see 

“Online resources” on page xi

 of this 

document. For information about Nautel training courses, go to the Nautel website at 

http://www.nautel.com/Training.aspx

CAUTION: FAILURE TO COMPLY WITH RECOMMENDATIONS MAY VOID 

YOUR MANUFACTURER’S WARRANTY. FOR MORE INFORMATION, REVIEW 

YOUR WARRANTY DOCUMENTS. 

Содержание Exporter Plus



























































































































































































Отзывы:

Нет отзывов