Nautel Exporter Plus Скачать руководство пользователя страница 150

Страница: 150 / 186

Exporter Plus Technical Instruction Manual

Operating

Page 8-80

Issue 1.0 2020-05-05

Software upgrade procedure

Exporter Plus software is easy to update using the UI’s

MAINTENANCE

menu. An update can

be performed over an Ethernet connection using TFTP. This requires that a TFTP server be

installed on the same Ethernet subnet as the Exporter Plus. Various TFTP server

implementations are available for Windows. SolarWinds Network Management provides a free

TFTP server at:

https://www.solarwinds.com/free-tools/free-tftp-server

Refer to your TFTP server’s software package for specific installation instructions. TFTP

servers require a designated folder to act as the TFTP server’s root directory (e.g., C:/TFTP-

Root). Make sure that the TFTP server is configured to both receive and transmit files to avoid

TFTP timeout conditions.

Preliminary Hardware and OS Compatibility Checks.

Before performing a software

upgrade to Exporter Plus SW version 1.10.0, check the following characteristics of your

Exporter Plus to make it is compatible for the upgrade:

• the hardware number (NAE97*), printed on the serial number label of the unit

• the version of operating system - see the OS field in the UI’s

MAINTENANCE

View

SW Version

screen.

• the version of single-board computer: see the CPU field in the UI’s

MAINTENANCE

View SW Version

screen. The latest version is indicated as Atom D425 (Nautel Part #

UA171); older Exporter Plus units may not have this.

Use the information above in

Table 8.3 on page 8-81

to determine the applicable upgrades

required prior to performing the software upgrade.

Note: If you are using a Windows-based computer with the Windows firewall turned on,

it will block the file transfer.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 150 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: