Nautel Exporter Plus Скачать руководство пользователя страница 151

Страница: 151 / 186

Exporter Plus Technical Instruction Manual

Operating

Issue 1.0 2020-05-05

Page 8-81

Table 8.3: Changes Required for Software Upgrade Compatibility

Procedure.

Perform a software update as follows:

1. Connect the Windows PC with the TFTP server to the Ethernet and configure its IP

address according to your Exporter Plus’ subnet. Verify the connection by pinging the

Exporter Plus’ IP address.

2. Place the software update file in the root directory of the TFTP server.

3. In the

MAINTENANCE

menu’s

Update File

screen, enter the software update file name

(see

Update file on page 8-76

4. In the

MAINTENANCE

menu’s

Update Host IP

screen, enter the IP address of the

computer that is running the TFTP server (see

Update host IP on page 8-75

5. Select

Run SW Update

from the

MAINTENANCE

menu to proceed with the update. The

UI will indicate the progress of the update and whether or not the file transfer and

decompression is successful. You can review the installation log on the UI.

6. Select

System Restart

from the

MAINTENANCE

menu to restart the Exporter Plus and

finalize the update.

Existing State

Changes Required

NAE97 to NAE97D,
with old CPU (not Atom D425)

Return the Exporter Plus to Nautel for CPU upgrade to Atom D425 (Nautel Part
# UA171), with OS 3.1.0 installed

NAE97 to NAE97D, with
Atom D425 CPU

Reflash the OS with version OS 3.0.0 or OS 3.1.0 from the Nautel FTP site.

NAE97E to NAE97K, with Atom
D425 CPU and OS 3.1.0

None. Exporter Plus is ready for SW 1.10.0 upgrade.

Note: OS Nautel’s Exporter Plus FTP site is:

http://www3.nautel.com/pub/Exporter%20Plus/Recovery/

Note: A software update resets all Exporter Plus settings to factory defaults. Make note of

any settings being altered and re-enter them when the software update is complete.

The following procedure shuts down the Exporter Plus software. Digital transmission is

disabled during this procedure.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 151 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: