Nautel Exporter Plus Скачать руководство пользователя страница 14

Страница: 14 / 186

Exporter Plus Technical Instruction Manual

Description

Page 1-2

Issue 1.0 2020-05-05

Figure 1.1: Exporter Plus in an FM HD radio system

Figure 1.2: Exporter Plus in an AM HD radio system

Note:

Other common system components, such as Ethernet switches and audio processors, are

not shown. They are described later.

Figure 1.1

and

Figure 1.2

are based on a combined

IBOC

system.

MPS Audio

GPS

Receiver

GPS

Antenna

Delayed

MPS Audio

(44.1 kHz)

Ethernet

Sample Rate

Converter

Exporter Plus

Coding

Delay

MPS Audio

(44.1 kHz)

MPS Audio

(44.1 kHz)

EXCITER

Transmitter

MPS Audio

GPS

Receiver

GPS

Antenna

Ethernet

Sample Rate

Converter

Exporter Plus

Coding

Delay

MPS Audio

(44.1 kHz)

MPS Audio

(44.1 kHz)

EXCITER

Transmitter

Stereo to

Mono

NOTE:

Mono = Left/2 + Right/2

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 14 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: