natus Olympic Warmette 48 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 50

natus Olympic Warmette 48 Скачать руководство пользователя страница 34

6-4

Olympic Warmette Models 48/49 and 55/56 Instruction Manual

Repair Procedures

Figure 6.1

Access panel assembly — exploded view

To reinstall the access panel:

1

Reinstall the access panel, then securely tighten the screws (see

2

Reinstall the shelf supports over the access panel, then securely tighten

the screws.

3

Place the tray on the shelf.

4

Test the Warmette for proper operation (see page 2-5).

Replacing the Mains Power Switch

Should you need to replace the mains power switch ( | / O ), perform the

following procedure.

Required Items:

Mains power switch (part no. 200001)

3/64-in. Allen wrench

1/4-in. nutdriver

To remove the mains power switch:

1

Press the power switch to the

OFF

(O) position, then unplug the power cord.

2

Remove the access panel (see

Removing the Access Panel

.

3

Disconnect the mains power switch spade connectors (see Figure 6.2).

Thermostat

Knob

Mains power

switch

Heater indicator
lamp cover

Heater indicator
lamp socket

Access panel

Spacer

Thermostat label

Mounting screws
(x2)

«
...
32
33
34
35
36
...
»

Содержание Olympic Warmette 48



















































Отзывы:

Нет отзывов