National 3425 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 33

National 3425 Скачать руководство пользователя страница 9

Page 9

MACHINE START UP PROCEDURE

TO RUN MACHINE

1. Machine MUST be off before plugging machine into power source.

2. Plug power cord into proper size extension cord.

3. Plug power cord into outlet.

4. Plug the motor cord plug into the handle cord plug if not connected.

5. Press down on handle slightly tilting machine back, lifting the grinding disk (disengaging) off from

the floor.

6. Depress lever on handle, motor will run.

7. Release lever for motor to stop.

8. Once machine is running, gently lower disk to the floor.

RUNNING MACHINE

WARNING:

DO NOT leave a plugged-in machine unattended.

Improper connection of the equipment-grounding conductor can result in a risk of electrical shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is
properly grounded. DO NOT modify the plug provided with this unit. If it will not fit the outlet, have a
proper outlet installed by a qualified electrician. NOTE: In Canada, the use of a temporary adapter is
not permitted by the Canadian Electrical Code.

Improper use of the grounding plug can result in a risk of electrical shock.

Know what you are removing. Scraping, sanding or grinding can release health hazardous dust and
liquids. Make sure you are following OSHA, State and/or Federal guidelines when removing hazardous
materials. Take necessary precautions and procedures. On some materials, grinding, scraping or
sanding are not allowed.

Figure 1

WARNING

: DO NOT lock lever on handle into a permanent on position. If operator would lose

control or be disabled, machine continues to operate. Do not defeat a switch or safety device.

Shroud
securing screws

Shroud

securing screws

«
...
7
8
9
10
11
...
»

Содержание 3425


































Отзывы:

Нет отзывов