National Instruments SCXI-1382 Скачать руководство пользователя страница 4

©

 National Instruments Corporation

3

SCXI-1382 Battery Pack Installation Guide

Battery Pack Safety Information

Note

Refer to the 

Read Me First: Safety and Radio-Frequency Interference

 document 

before removing equipment covers or connecting or disconnecting any power wires or 
signal wires.

Cautions

The battery pack contains a sealed lead-acid non-wet, nonspillable battery.

Do 

not

 ship the battery pack without proper packaging or if it is damaged. Retain the 

original packaging for future shipping.

Do 

not

 carry the battery pack onto a passenger plane. You must ship the battery pack as 

cargo.

You must recycle or properly dispose of the battery. In the United States, call 
1-800-RE-USE-Pb (1-800-738-7372) for more information.

Never

 expose the battery to fire or short-circuit the battery.

Do 

not

 use the battery pack if it appears damaged.

Always use the supplied charger to charge the battery pack. Follow the documentation 
instructions. You can obtain NI documents at 

ni.com

 or by contacting an NI sales 

representative.

Charging the Battery Pack

The SCXI-1382 battery pack requires 12 to 14 VDC and at least 3.7 A of 
power for at least 12 to 14 hours to reach a full charge. Charge the battery 
pack as soon as possible after use. If the battery is fully charged, it can 
power the SCXI-1000DC chassis for more than five hours. However, 
NI recommends that you charge the battery after every three hours of use 
to extend the life of the battery pack.

Note

NI recommends using the SCXI-1383 power supply/float charger to charge the 

SCXI-1382 battery pack. Refer to the 

SCXI-1383 Power Supply/Float Charger 

Installation Guide

 for charging instructions.

Caution

The battery pack contains a sealed lead-acid battery that contains toxic material 

(lead) and corrosive fluid (sulfuric acid). Charging can produce explosive gases. Do 

not

 

charge the battery in gas-tight enclosures. Charge the battery in a well ventilated area away 
from sparks, flames, or smoke. Do 

not

 short the battery pack terminals, as this can cause 

an explosion or fire. Do 

not

 store the battery pack in a discharged state. Do 

not

 puncture, 

disassemble, mutilate, or incinerate the battery pack. Recycle the battery or dispose of the 

Содержание SCXI-1382












Отзывы: