background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

371177A-01               

© Copyright 1993, 1994 National Instruments Corporation.  All rights reserved.

March 1993

 

 

 

 

 NATIONAL 

INSTRUMENTS

®

The Software is the Instrument

®

Installation Guide

                                                                             

SCXI-1345 Shielded Cable

This guide describes how to install the SCXI-1345 shielded cable with an adapter board between

an SCXI module and a data acquisition board.  In addition to the SCXI-1345 kit contents, you

will also need an SCXI chassis, an SCXI module, a computer, a multifunction I/O (MIO) board,

a small Phillips-head screwdriver, and a small flathead screwdriver.

Introduction

With the SCXI-1345 shielded cable, you can make a low-noise, long-distance connection

between your SCXI chassis and your MIO board.  You can use the SCXI-1345 with the

following MIO boards:

PC/XT, PC AT

Macintosh

AT-MIO-16

NB-MIO-16

AT-MIO-16F-5

NB-MIO-16X

AT-MIO-16X

The SCXI-1345 shielded cable consists of a 1, 2, 5, or 10 m round cable that has a 50-pin female

connector with a grounding strap at one end and a 68-pin female connector at the other end.

When plugged into the SCXI-1345 adapter board, the shielded cable brings the pinout of the

MIO board I/O connector to the SCXI module and to a breakout connector you can use with

other SCXI accessories, such as the SCXI-1180 and the SCXI-1351.

What Your Kit Should Contain

The SCXI-1345 shielded cable kit is available in four cable sizes:  1, 2, 5, or 10 m.

In addition, each version of the kit contains the following components:

¥ Cable adapter assembly

¥ Two small screws

¥ Replacement bracket for AT-MIO-16 boards

Содержание SCXI-1345








Отзывы: