background image

8

|

ni.com

|

RM-4339 Calibration Procedure

2.

Acquire voltage measurements from all channels with the NI PXIe-4339.
a.

Create and configure an AI voltage measurement according to the values found in 
Table 4.

b.

Start the task by calling DAQmx Start Task.

c.

Average the readings that you acquired and record the vales as 

VoffsetPXIe-4339Chx

where 

x

 is the channel number.

d.

Clear the task by calling DAQmx Clear Task.

3.

Remove the TB-4339/B/C from the SH96-96-2 cable and connect the SH96-96-2 cable to 
the 96-pin connector on the back of the RM-4339.

4.

Connect an RJ50 cable to each channel with AI+ (pin 2) and AI- (pin 3) connected to 
T- (pin 9).

5.

Acquire voltage measurements from all channels with the NI PXIe-4339.
a.

Create and configure an AI voltage measurement according to the values found in 
Table 4.

b.

Start the task by calling DAQmx Start Task.

c.

Average the readings that you acquired and subtract 

VoffsetPXIe-4339Chx

 from the 

average values for each channel.

Table 4.  

AI Voltage Mode Setup

Configuration

Value

Channel Name

Dev1/ai0:7

Measurement Type

AI Voltage

Maximum Value

0.01

Minimum Value

-0.01

Units

Volts

Input Terminal Configuration

Default

Sample Mode

Finite Samples

Sample Clock Rate

100

Samples per Channel

100

Содержание RM-4339














Отзывы: