manualshive.com logo in svg

National Instruments PXIe-5667, Руководство по началу работы

Поделиться
Скачать
National Instruments PXIe-5667 Скачать руководство пользователя страница 26

•

When there is a change to the system cabling

•

When the system is in an environment where external variables, such as temperature, can

affect measurements

You should also perform a self-calibration if your device has exceeded any of the following

temperature or time limits since the last device self-calibration:
•

IF flatness: ±5 °C and/or 7 days

•

Gain reference: ±5 °C and/or 7 days

•

LO self-calibration: ±10 °C and/or 30 days

•

Digitizer self-calibration: ±5 °C and/or 90 days

Performing a Device Self-Calibration Using the
NI-RFSA SFP

NI recommends you run the self-calibration from the NI-RFSA Soft Front Panel (SFP). You

can also run a self-calibration programmatically using the NI-RFSA API.
1. Launch the NI-RFSA SFP by navigating to 

Start

»

All Programs

»

National

Instruments

»

NI-RFSA

»

NI-RFSA Soft Front Panel

.

2. Click 

Device/System

»

Calibration

»

Self Calibration

.

3. Select the self-calibration steps you want to perform from the 

Self-Calibration

 dialog

box.

4. Click 

Next

 to run the self-calibration.

NI PXIe-5667 (3.6 GHz) Getting Started Guide

  | 

© National Instruments

  | 

25

Содержание PXIe-5667


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды