National Instruments PXIe-4353 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 20

National Instruments PXIe-4353 Скачать руководство пользователя страница 14

NI PXIe-4353 and TB-4353 Terminal Block Installation Guide

14

ni.com

The TB-4353 contains eight thermistors that are used to measure the temperature of the adjacent screw
terminal junctions for the CJC that is performed when computing the thermocouple temperature
measurement. These eight thermistors are measured using the CJC channels on the NI PXIe-4353
module. Each thermistor measures the CJC temperature for a subset of associated thermocouple
channels as shown in Figure 10. The dashed lines indicate the channel to CJC associations.NI-DAQmx
automatically associates the correct thermistor with the thermocouple measurements when you use the

Thermocouple Channel-Type

and select

built-in

for the CJC source.

Figure 10.

TB-4353 CJC Grouping Locations

1

CJC0

2

CJC1

3

CJC2

4

CJC3

5

CJC4

6

CJC5

7

CJC6

8

CJC7

Table 2.

CJC to Thermocouple Channels Associations

CJC

Associated Thermocouples

CJC

Associated Thermocouples

CJC0

AI <0..2>

CJC4

AI <11..13>,

AI <19..21>

CJC1

AI <3..5>

CJC5

AI <14, 15>,

AI <22, 23>

CJC2

AI <6, 7>

CJC6

AI <24..27>

CJC3

AI <8..10>,

AI <16..18>

CJC7

AI <28..31>

COM

TC0

TC1

TC2

TC

3

TC4

TC5

TC6

TC7

TC

8

T

C

9

TC10

TC11

TC12

TC1

3

TC14

TC15

TC1

8

TC17

TC16

TC19

TC20

TC21

TC22

TC2

3

TC26

TC25

TC24

TC27

TC2

8

TC29

TC

3

0T

C

3

1

+ – + – + – + – + – + – + – + –

+ – + – + – + – + – + – + – + –

+ – + – + – + – + – + – + – + –

+ – + – + – + – + – + – + – + –

1

2

5

3

6

8

4

7

«
...
12
13
14
15
16
...
»

Содержание PXIe-4353





















Отзывы:

Нет отзывов