National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 Скачать руководство пользователя

Страница: 46 / 83

Chapter 3

I/O Information

3-6

ni.com

Ethernet

Figure 3-4 shows the location and pinouts for the Ethernet connector on the
NI PXI-8108. Table 3-4 lists and describes the Ethernet connector signals.

Figure 3-4.

Ethernet Connector Location and Pinout

Note

The Ethernet controller can perform automatic crossover, thus eliminating the need

for crossover cables.

Table 3-4.

Ethernet Connector Signals

Pin

Fast Ethernet

Gigabit Ethernet

TX+

TX_A+

TX–

TX_A–

RX+

RX_B+

TX_C+

TX_C–

RX–

RX_B–

RX_D+

RX_D–

Ethernet

NI PXI-8108

Embedded Controller

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108




















































































Результаты поиска

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108

Отзывы:

Похожие инструкции для PXI/CompactPCI Embedded Computer NI PXI-8108

Бренды по названию

Популярные бренды

National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108, Руководство пользователя

Результаты поиска

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108

Отзывы:

Похожие инструкции для PXI/CompactPCI Embedded Computer NI PXI-8108

Бренды по названию

Популярные бренды