National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 Скачать руководство пользователя

Страница: 32 / 83

Chapter 2

Installation and Configuration

NI PXI-8108 User Manual

2-18

ni.com

Note

When any IP or identification settings are changed, you will be prompted to reboot

the controller for the changes to take effect. Click

Yes

to automatically reboot the RT

target. You may also reboot the controller by right-clicking on the target name under

Remote Systems

and selecting

Reboot

After rebooting the PXI controller it will appear in the

Remote Systems

category with the assigned name.

Figure 2-4 shows the RT Series PXI target,

PXI-8106

, configured to

automatically obtain an IP address from a DHCP server, as indicated in the

IP Settings

section of the figure.

Figure 2-4.

Configuring RT Target Network Settings

Expand the PXI controller view in the

Remote Systems

branch and

select

Software

Click the

Add/Remove Software

button in the toolbar to launch the

LabVIEW Real-Time Software Wizard.

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108




















































































Результаты поиска

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108

Отзывы:

Похожие инструкции для PXI/CompactPCI Embedded Computer NI PXI-8108

Бренды по названию

Популярные бренды

National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108, Руководство пользователя

Результаты поиска

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108

Отзывы:

Похожие инструкции для PXI/CompactPCI Embedded Computer NI PXI-8108

Бренды по названию

Популярные бренды