National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 Скачать руководство пользователя | Manualshive

Страница: 23 / 83

background image

Chapter 2

Installation and Configuration

©

National Instruments Corporation

2-9

NI PXI-8108 User Manual

ExpressCard Configuration Submenu

Use this submenu to apply alternate settings to the ExpressCard
configuration. These settings determine how much memory space,
I/O space, and PCI bus numbers will be pre-allocated for the
ExpressCard port, allowing non-PCI Express-aware operating systems to
support hot-plugging ExpressCard devices. Normally, you do not need to
modify these settings, as the factory default settings provide the most
compatible and optimal configuration possible.

•

Reserved Buses

—This setting determines the number of PCI buses

that will be reserved by the BIOS for ExpressCard PCI-PCI bridges
that may be hot-plugged in the ExpressCard slot. The default value for
this setting is

8

PCI buses.

•

Reserved Memory

—This setting determines the amount of memory

space, in bytes, that will be reserved by the BIOS for PCI-PCI bridges
that may be hot-plugged in the ExpressCard slot. The default value for
this setting is

32M

bytes of memory.

•

Reserved I/O

—This setting determines the amount of I/O space, in

bytes, that will be reserved by the BIOS for PCI-PCI bridges that may
be hot-plugged in the ExpressCard slot. The default value for this
setting is

4K

bytes of I/O space.

USB Configuration Submenu

Use this submenu to apply alternate configurations to the USB ports.
Normally, you do not need to modify these settings, as the factory default
settings provide the most compatible and optimal configuration possible.

•

USB Devices

—This item lists the total number of devices detected in

the system, categorized by device type.

•

Legacy USB Support

—This setting specifies whether or not legacy

USB support is enabled. Legacy USB support refers to the ability to
use a USB keyboard and mouse during system boot or in a legacy
operating system such as DOS. The default value is

Enabled

.

Note

Certain real-time applications may require you to disable this setting to reduce loop

time jitter. When the controller is configured to boot LabVIEW RT, legacy USB support is
automatically disabled.

•

Device Reset Delay

—This setting specifies the number of seconds the

Power-On Self Test will wait for a USB mass storage device to start.
The default is

20

seconds.

«
...
21
22
23
24
25
...
»

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108




















































































Отзывы:

Нет отзывов

Похожие инструкции для PXI/CompactPCI Embedded Computer NI PXI-8108

Бренд: Rain Bird Страницы: 48

Бренд: Mamas & Papas Страницы: 16

Бренд: Samsung Страницы: 32

Бренд: B&R Industries Страницы: 89

Бренд: Danfoss Страницы: 37

Бренд: Daikin Страницы: 44

Бренд: Nacon Страницы: 24

Бренд: NAD Страницы: 4

Бренд: NAD Страницы: 4

Бренд: olympia electronics Страницы: 10

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 20

VeriSafe VS2-NET

Бренд: Panduit Страницы: 6

Бренд: Fancom Страницы: 23

Бренд: Beninca Страницы: 7

Бренд: TFK Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды