National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 Скачать руководство пользователя | Manualshive

Страница: 26 / 83

background image

Chapter 2

Installation and Configuration

NI PXI-8108 User Manual

2-12

ni.com

Boot Setup Menu

Use this menu to configure settings related to the boot process and boot
device priority.

•

Boot Settings Configuration

—Use this setting to access the

Boot

Settings Configuration

submenu. Refer to the

Boot Settings

Configuration Submenu

section for more information.

•

SCSI Drive Boot

—This setting specifies whether or not boot support

is enabled for legacy mass storage devices, such as SCSI drives. When
enabled, legacy mass storage controllers with boot support will be
displayed in the

Boot Option Priorities

menu. The default value is

Enabled

.

•

PXE Network Boot

—This setting specifies whether or not the PXE

network boot agent is enabled. When enabled, the Intel Boot Agent
will be displayed in the

Boot Option Priorities

menu, allowing you to

boot from a PXE server on the local subnet. Note that the Intel Boot
Agent device is named

IBA GE Slot 00c9 v1310

in the

Boot Option

Priorities

menu. The system must be restarted for this setting to take

effect. The default value is

Disabled

.

•

Boot Option Priorities

—These settings specify the order in which the

BIOS checks for bootable devices, including the local hard disk drive,
removable devices such as USB flash disk drives or USB CD-ROM
drives, or the PXE network boot agent. The BIOS will first attempt to
boot from the device associated with

1st Boot Device

, followed by

2nd Boot Device

, and

3rd Boot Device

. If multiple boot devices are

not present, the BIOS setup utility will not display all of these
configuration options. To select a boot device, press <Enter> on the
desired configuration option and select a boot device from the resulting
menu. You can also disable certain boot devices by selecting

Disabled

.

Note

Only one device of a given type will be shown in this list. If more than one device

of the same type exists, use the

Device BBS Priorities

submenus to re-order the priority of

devices of the same type.

The following submenus will be displayed if one or more bootable devices
of the corresponding type is present:

•

Hard Drive BBS Priorities

—Use this setting to access the

Hard

Drive BBS Priorities

submenu to re-order or disable bootable hard

drive devices. Refer to the

Hard Drive BBS Priorities Submenu

section

for more information.

«
...
24
25
26
27
28
...
»

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108




















































































Отзывы:

Нет отзывов

Похожие инструкции для PXI/CompactPCI Embedded Computer NI PXI-8108

Бренд: E-fly Страницы: 16

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Eaton Страницы: 288

Бренд: Eaton Страницы: 28

Бренд: Parallel Страницы: 16

Бренд: V2 Страницы: 46

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: Taco Electronic Solutions Страницы: 28

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренд: Parker Страницы: 54

Бренд: RAM Страницы: 71

PowerFlex 755 IP00

Бренд: Allen-Bradley Страницы: 78

TruPortal TP-ADD-1DIP

Бренд: Interlogix Страницы: 9

Бренд: Polycom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды