National Instruments PCI-8361 Скачать руководство пользователя

Страница: 43 / 128

A-1

Specifications

This appendix lists the system specifications for the following products only:
•

PCI-8361 (199392x-01L)

•

PCI-8366 (199392x-02L)

•

PCIe-8361 (199042A/B/C-01L)

•

PCIe-8362 (190735x-01L)

•

PCIe-8363 (199042x-01L)

•

PXI-8360 (191373x-01)

•

PXI-8364 (199991x-02L)

•

PXI-8367 (199991x-04L)

•

PXI-8368 (157298x-02L)

•

PXIe-8360 (194402x-01L)

•

PXIe-8364 (193970x-01L)

•

ExpressCard-8360 (198266x-01L)

Note

The model numbers listed below are followed by their specific NI assembly

numbers in parentheses.

denotes all letter revisions of the assembly. Ensure the

specifications of interest match the NI assembly number that is printed on either the
front or back side of the board.

For specifications on previous generations of products, refer to Appendix B,

Specifications for

Legacy Products

PCI-8361 (199392

-01L)

Note

These specifications are typical at 25 °C, unless otherwise stated, and are

subject to change without notice.

Physical

Dimensions

6.3 cm × 12.1 cm (2.48 in. × 4.76 in.)

Maximum cable length

7 m

Slot requirements

One PCI slot (standard height or low profile)

Содержание PCI-8361

































































































































Результаты поиска

Содержание PCI-8361

Отзывы:

Похожие инструкции для PCI-8361

Бренды по названию

Популярные бренды

National Instruments PCI-8361, Руководство пользователя

Результаты поиска

Содержание PCI-8361

Отзывы:

Похожие инструкции для PCI-8361

Бренды по названию

Популярные бренды