National Instruments PCI-6238 Скачать руководство пользователя страница 56

Страница: 56 / 173

Chapter 5

Analog Output

NI 6238/6239 User Manual

5-4

ni.com

the buffer at a fast enough rate to keep up with the generation, the buffer
will underflow and cause an error.

Analog Output Triggering

Analog output supports two different triggering actions:

•

Start trigger

•

Pause trigger

A digital trigger can initiate these actions. NI 6238/6239 devices support
digital triggering, but do not support analog triggering. Refer to the

Start Trigger Signal

and

AO Pause Trigger Signal

sections for more

information on these triggering actions.

Connecting Analog Current Output Signals

AO <0..1> are the current output signals for AO channels 0 and 1. AO GND
is the ground reference for AO <0..1>.

Figure 5-2 shows how to make analog current output connections to the
device.

Figure 5-2.

Analog Current Output Connections

Tip

Internal voltage drop for the NI 6238/6239 devices is a maximum of 3 V relative to

the externally supplied voltage.

Caution

The maximum output voltages rating of AO signals and input voltage ratings for

AO power supply with respect to AO GND and earth/chassis ground are listed in the

User-
Provided
Load

–

User-

Provided

Power

Supply

DAC

Internal
Voltage

Drop

AO Power
Supply Pin

User-Provided
AO GND

AO GND

NI 6238/6239

Содержание PCI-6238














































































































































































Результаты поиска

Содержание PCI-6238

Отзывы:

Похожие инструкции для PCI-6238

Бренды по названию

Популярные бренды

National Instruments PCI-6238, Руководство пользователя

Результаты поиска

Содержание PCI-6238

Отзывы:

Похожие инструкции для PCI-6238

Бренды по названию

Популярные бренды