National Instruments PCI-6238 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 173

background image

Chapter 11

Bus Interface

NI 6238/6239 User Manual

11-2

ni.com

Each DMA controller supports packing and unpacking of data through the
FIFOs to connect different size devices and optimize PCI bus utilization
and automatically handles unaligned memory buffers.

PXI Considerations

Note

PXI clock and trigger signals are only available on PXI devices. Other devices use

RTSI.

PXI Clock and Trigger Signals

Refer to the

,

,

PXI_STAR Trigger

, and

PXI_STAR Filters

sections of Chapter 10,

Digital Routing and Clock

, for more information on PXI clock and trigger signals.

PXI and PXI Express

NI PXI-6238/6239 modules can be installed in any PXI chassis and most
slots of PXI Express chassis.

PXI specifications are developed by the PXI System Alliance
(

www.pxisa.org

). Using the terminology of the PXI specifications,

NI PXI-6238/6239 devices are

3U Hybrid Slot-Compatible PXI-1

Peripheral Modules

.

3U

designates devices that are 100 mm tall (as opposed to the taller 6U

modules).

Hybrid slot-compatible

defines where the device can be installed.

PXI-6238/6239 devices can be installed in the following chassis and slots:

•

PXI chassis

—PXI-6238/6239 devices can be installed in any

peripheral slot of a PXI chassis.

•

PXI Express chassis

—PXI-6238/6239 devices can be installed in the

following PXI Express chassis slots:

–

PXI-1 slots

—Accepts all PXI modules

–

PXI hybrid slots

—Accepts PXI or PXI Express modules.

PXI-1

devices use PCI signaling to communicate to the host controller (as

opposed to PCI Express signaling).

Peripheral

devices are installed in peripheral slots and are not system

controllers.

«
...
127
128
129
130
131
...
»

Содержание PCI-6238














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PCI-6238

Бренд: TCS Страницы: 16

Бренд: Graco Страницы: 166

Бренд: Aiphone Страницы: 2

sundi GLASSO GNT-248

Бренд: Zamel Страницы: 6

Бренд: Elvox Страницы: 36

Бренд: Datavideo Страницы: 40

3D TRASAR Series

Бренд: Nalco Страницы: 243

ONECONCEPT 10029361

Бренд: Chal-tec Страницы: 29

Бренд: red lion Страницы: 8

Бренд: SKF Страницы: 63

Бренд: GeoVision Страницы: 4

Бренд: ATL Страницы: 46

Бренд: BIO-MICROBICS Страницы: 12

Бренд: JCM Страницы: 11

Бренд: V-Tec Страницы: 8

Бренд: MAHA Страницы: 28

Бренд: GATE ARMS+ Страницы: 12

Бренд: FingerTec Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды