National Instruments NI REM-11115 Скачать руководство пользователя страница 10

Страница: 10 / 14

Figure 5. REM-11115 Current Output Connection

24 VDC

A0 (0:3) Voltage

A0 (0:3) Current

COM

REM-11115

–

Load

Note

For information about fuse ratings for the REM-11115, refer to the device

datasheet on

ni.com/manuals

Connection Guidelines

•

Always connect analog signals using shielded, twisted pair cables. Unshielded cables
may lead to values outside the specified tolerance limits in environments subject to heavy
noise.

•

Connect the cable shield to functional earth ground immediately after the cables enter the
control cabinet.

•

Connect the cable shield to a shield bus if you are not using a closed control cabinet.

•

NI recommends using the NI Remote I/O Shield Set for optimal shield connection.

•

Make sure that devices you connect to the REM-11115 are compatible with the module
specifications.

•

Push the wire into the terminal when using a solid wire or a stranded wire with a ferrule.

•

Open the terminal by pressing a screwdriver into the spring lever when using a stranded
wire without a ferrule.

ni.com

REM-11115 Getting Started Guide

Содержание NI REM-11115















Результаты поиска

Содержание NI REM-11115

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI REM-11115, Руководство по началу работы

Результаты поиска

Содержание NI REM-11115

Отзывы:

Бренды по названию

Популярные бренды