National Instruments NI PXIe-8130 Скачать руководство пользователя

Страница: 58 / 84

National Instruments Corporation

4-1

NI PXIe-8130 User Manual

Common Configuration
Questions

This chapter answers common configuration questions you may have when
using a NI PXIe-8130 embedded controller.

General Questions

What do the LEDs on the NI PXIe-8130 front panel mean?

Refer to the LED status descriptions in the

Front Panel Features

section of

Chapter 3,

I/O Information

After shutting down my NI PXIe-8130 controller, the Ethernet LEDs
continue to blink. Is it safe to remove my controller or disconnect
power?

The NI PXIe-8130 controller Ethernet device remains powered even after
shutdown. It is safe to remove your controller or disconnect power.

How do I check the configuration of the memory, hard drive,
time/date, and so on?

You can view these parameters in the BIOS setup. To enter the BIOS setup,
reboot the NI PXIe-8130 and press <Delete> during the memory tests.
Refer to the

Accessing the BIOS Setup Utility

section of Chapter 2,

Installation and Configuration

, for more information.

Can I use the internal Serial ATA drive and an external hard drive at
the same time?

Yes. Refer to the

BIOS Setup Utility

section of Chapter 2,

Installation and

Configuration

, for more information.

Содержание NI PXIe-8130





















































































Результаты поиска

Содержание NI PXIe-8130

Отзывы:

Похожие инструкции для NI PXIe-8130

Бренды по названию

Популярные бренды

National Instruments NI PXIe-8130, Руководство пользователя

Результаты поиска

Содержание NI PXIe-8130

Отзывы:

Похожие инструкции для NI PXIe-8130

Бренды по названию

Популярные бренды