National Instruments NI PXIe-5601 Скачать руководство пользователя страница 9

Страница: 9 / 45

NI PXIe-5601 Calibration Procedure

IF Output Calibration

Use the results of the IF output calibration procedure in the following procedures:
•

Absolute Gain Accuracy Verification

•

Average Noise Level Verification

•

Reference Level Adjustment for RF Frequencies

≤

120 MHz

•

Reference Level Adjustment for RF Frequencies

≥

120 MHz

•

IF Attenuation Calibration Adjustment

•

IF Response Adjustment

Connect the power splitter input to the RF source output through the 3.5 mm-to-3.5 mm
cable.

Connect power sensor A to the previously designated reference output of the power splitter.

Connect the other output of the power splitter to the spectrum analyzer input through the
3.5 mm-to-3.5 mm cable. Figure 3 shows the completed equipment setup.

Figure 3.

IF Output Equipment Setup

Measure the channel A power and the spectrum analyzer power, using the appropriate
frequency for the power sensor, using the following settings:
•

RF source power (for both 53 MHz and 187.5 MHz): 0 dBm

•

Reference level: 0 dBm

RF Source

Power Splitter

Power Sensor A

Power Meter

Power Meter Channel A

Spectrum Analyzer

Spectrum Analyzer Input

Содержание NI PXIe-5601














































Результаты поиска

Содержание NI PXIe-5601

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI PXIe-5601, Процедура калибровки

Результаты поиска

Содержание NI PXIe-5601

Отзывы:

Бренды по названию

Популярные бренды