National Instruments NI PXIe-5601 Скачать руководство пользователя страница 35

Страница: 35 / 45

NI PXIe-5601 Calibration Procedure

22. Commit the settings to hardware using the niRFSA Initiate VI or the

niRFSA_Initiate

function.

23. Wait 200 ms.
24. Measure the

Channel A Power

. Calculate

RF Power

using the following equation:

RF Power

Channel A Power

RF Input Calibration Factor

Use the appropriate RF frequency for the channel A sensor. Calculation of the

RF Input

Calibration Factor

may require linear interpolation.

25. Measure and record the channel B power. This value is the

IF Power

. Make this

measurement using the appropriate IF frequency for the channel B sensor.

26. Calculate

Gain

using the following formula:

Gain

IF Power

RF Power

27. Store the appropriate calibration constants using the niRFSA Cal Adjust IF Attenuation

Calibration VI or the

niRFSA_CalAdjustIFAttenuationCalibration

function.

You must provide the following information:
•

IF filter

•

Attenuation settings in a two-element array [IF1, IF2]

•

Gain

from step 26

28. Repeat steps 21 to 27 for all possible combinations of IF attenuation settings from the valid

values in Table 22.

Note

NI recommends keeping your RF signal generator enabled when repeating

steps unless making a connection change. Keeping the signal generator enabled
reduces the wear on the RF signal generator relays. After making a connection
change and enabling your generator, wait 5 seconds for the system to settle.

29. Repeat steps 14 to 28 for all

IF Filters

in Table 21.

30. Close the NI 5601 IF attenuation calibration step using the niRFSA Close Calibration

Step VI or the

niRFSA_CloseCalibrationStep

function.

31. Close the external calibration by calling the niRFSA Close Ext Cal VI with the

action

parameter set to

Commit

or by calling the

niRFSA_CloseExtCal

function with the

action

parameter set to

NIRFSA_VAL_EXT_CAL_COMMIT

32. Close the niRFSG session using the niRFSG Close VI or the

niRFSG_close

function.

Table 22.

IF Attenuator Settings

IF1 Attenuator

IF2 Attenuator

0 dB to 15 dB in 1 dB steps

Содержание NI PXIe-5601














































Результаты поиска

Содержание NI PXIe-5601

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI PXIe-5601, Процедура калибровки

Результаты поиска

Содержание NI PXIe-5601

Отзывы:

Бренды по названию

Популярные бренды