manualshive.com logo in svg

National Instruments NI PXIe-5601, Процедура калибровки

Поделиться
Скачать
National Instruments NI PXIe-5601 Скачать руководство пользователя страница 18

18

|

ni.com

|

NI PXIe-5601 Calibration Procedure

5.

Set the NI 5601 reference level according to Table 8 using the niRFSA Configure 
Reference Level VI or the 

niRFSA_ConfigureReferenceLevel

 function.

6.

Set the RF attenuation according to Table 8 using the niRFSA Attenuation property or the 

NIRFSA_ATTR_ATTENUATION

 attribute.

7.

Set the NI 5601 center frequency according to Table 9 and set the span according to Table 8 
using the Center Span instance of the niRFSA Configure Spectrum Frequency VI or the 

niRFSA_ConfigureSpectrumFrequencyCenterSpan

 function.

8.

Commit the settings to hardware using the niRFSA Initiate VI or the 

niRFSA_Initiate

 

function.

9.

Set the spectrum analyzer using the following settings:
•

Reference level: -50 dBm

•

Frequency span: 100 Hz

•

Resolution bandwidth: 3 kHz

•

Video bandwidth: 10 Hz

•

Center frequency: Refer to Table 9

10. Use the spectrum analyzer noise marker to measure the average noise.
11. Record the average noise measured on the spectrum analyzer. This value is the 

Measured 

Noise

 and is used in step 13.

12. Recall the 

NI 5601 Stored Gain

 for each setting using the niRFSA Downconverter Gain 

property or the 

NIRFSA_ATTR_DOWNCONVERTER_GAIN

 attribute.

13. Calculate the 

NI 5601 Input Noise

 using the following formula:

NI 5601 Input Noise

 = 

Measured Noise

 + 

IF Calibration Factor 

- 

NI 5601 Stored Gain

14. Compare the 

NI 5601 Input Noise

 to the limits in Table 11.

Table 8.  

NI 5601 Settings

Frequency Range

Reference 

Level

RF Attenuation

Span

10 MHz to 30 MHz

-10 dBm

0 dB

10 Hz

30 MHz to 6,600 MHz

-50 dBm

0 dB

10 Hz

Table 9.  

Center Frequency Settings

NI 5601 Center Frequency

Spectrum Analyzer 

Center Frequency

10 MHz to <120 MHz

187.5 MHz

120 MHz to <330 MHz

53 MHz

330 MHz to 6.6 GHz

187.5 MHz

Содержание NI PXIe-5601














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды