National Instruments NI PXIe-5601 Скачать руководство пользователя страница 13

Страница: 13 / 45

NI PXIe-5601 Calibration Procedure

11. If you used the spectrum analyzer, set the reference level, frequency span, and resolution

bandwidth according to Table 4. Set the center frequency according to Table 5.

12. Set the RF source to the same frequency you set for the NI 5601 center frequency according

to Table 3.

13. At each NI 5601 center frequency and reference level setting, perform the following steps:

Adjust the RF source power, in dBm, using the following equation:

Channel A Power

RF Input Attenuated Calibration Factor

Reference Level

±1 dB

When making the adjustment, use the appropriate RF frequency for the channel A
sensor. Calculation of the

RF Input Attenuated Calibration Factor

may require linear

interpolation.

Note

Set the signal generator to its maximum power if it does not have sufficient

power to reach the reference level.

Record the channel A power.

Measure the channel B power or spectrum analyzer power using one of the following
methods:
•

If you are using the power meter, measure and record the channel B power. Use
the appropriate IF frequency from Table 5 for the channel B sensor.

•

If you are using the spectrum analyzer, measure and record the

Spectrum

Analyzer Power

. Correct the

Spectrum Analyzer Power

using the appropriate

IF Calibration Factor

for the IF frequency in Table 5 and the following formula:

Corrected Spectrum Analyzer Power

Spectrum Analyzer Power

IF Calibration Factor

Table 4.

Spectrum Analyzer Settings

Parameter

Value

Reference Level

0 dBm

Frequency Span

10 Hz

Resolution Bandwidth

200 Hz

Table 5.

Spectrum Analyzer Center Frequency Settings

NI 5601 Center Frequency

IF Frequency (Spectrum Analyzer

Center Frequency)

10 MHz to <120 MHz

187.5 MHz

120 MHz to <330 MHz

53 MHz

330 MHz to 6.6 GHz

187.5 MHz

Содержание NI PXIe-5601














































Результаты поиска

Содержание NI PXIe-5601

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI PXIe-5601, Процедура калибровки

Результаты поиска

Содержание NI PXIe-5601

Отзывы:

Бренды по названию

Популярные бренды