background image

Table 1.

 Required Equipment for Calibration

Required

Equipment

Recommended Model(s)

Where Used

Minimum

Specifications

 

 

 

 

Digital multimeter

(DMM)

Agilent 3458A

1

All parameters

Voltage: <±26 ppm

accuracy and <1 µV

resolution

Current: <±100 ppm

accuracy and <5 pA

resolution

Two 50 Ω resistors

Vishay

PTF5650R000BZEK

Voltage remote

sense

0.1% tolerance, 1/8 W

Two 10 Ω resistors

Vishay

CMF5510R000BEEK

Current remote

sense

0.1% tolerance, 1/4 W

Two 100 Ω

resistors

Vishay

PTF65100R00BYEK

Current remote

sense

0.1% tolerance, 1/4 W

Two 1 kΩ resistors

Vishay

PTF651K0000BYEK

Voltage and

current remote

sense

0.1% tolerance, 1/4 W

Two 10 kΩ

resistors

Vishay

PTF6510K000BYEK

Current remote

sense

0.1% tolerance, 1/4 W

Two 100 kΩ

resistors

Vishay

PTF65100K00BYEK

Current remote

sense

0.1% tolerance, 1/4 W

Test Conditions

The following setup and environmental conditions are required to ensure the NI 4141 meets
published specifications:

Keep cabling as short as possible. Long cables act as antennas, picking up extra noise that
can affect measurements.

Verify that all connections to the device, including front panel connections and screws,
are secure.

Ensure that the PXI chassis fan speed is set to HIGH, that the fan filters (if present) are
clean, and that the empty slots contain slot blockers and filler panels. For more

1

To take measurements in the 10 µA range with the Agilent 3458A, you must send your device to
the Agilent Primary Standards Lab for a special calibration to verify the 10 µA, 1 µA, and 100 nA
ranges.

NI PXIe-4141 Calibration Procedure

  | 

© National Instruments

  | 

3

Содержание NI PXIe-4141





















Отзывы: