National Instruments NI cDAQTM-9138 Скачать руководство пользователя

Страница: 16 / 141

1-7

NI cDAQ-9138/9139 User Manual

Figure 1-2.

Ring Lug Attached to Ground Terminal

Note

Make sure that no I/O-side power is connected to the I/O module. If the

chassis is in a nonhazardous location, the chassis power can be on when you install
I/O modules.

Align the I/O module with a cDAQ chassis slot. The module slots are labeled 1 to 8, left to
right.

Squeeze the latches and insert the I/O module into the module slot, and press firmly on the
connector side of the I/O module until the latches lock the I/O module into place.
Repeat these steps to install additional I/O modules.

Verify that the DISABLE RT DIP switch is in the ON position so that the chassis boots into
the Windows operating system. Refer to the

DIP Switches

section for more information

about the DISABLE RT DIP switch.

Figure 1-3.

DISABLE RT DIP Switch in ON Position

NI cD

-913

NI C

omp

act

DISABLE RT
SAFE MODE
CONSOLE OUT
IP RESET
NO APP
USER1

OFF

Содержание NI cDAQTM-9138














































































































































Результаты поиска

Содержание NI cDAQTM-9138

Отзывы:

Похожие инструкции для NI cDAQTM-9138

Бренды по названию

Популярные бренды

National Instruments NI cDAQTM-9138, Руководство пользователя

Результаты поиска

Содержание NI cDAQTM-9138

Отзывы:

Похожие инструкции для NI cDAQTM-9138

Бренды по названию

Популярные бренды