National Instruments NI cDAQTM-9138 Скачать руководство пользователя | Manualshive

Страница: 37 / 141

background image

1-28

|

ni.com

Chapter 1

Getting Started with the cDAQ Chassis

4.

Power on the MXI-Express device.

5.

Power on the cDAQ chassis.

The MXI-Express port has one LINK LED. Refer to Table 1-8 for information about the
MXI-Express LINK LED behavior.

Note

Do

not

connect MXI-Express devices to the cDAQ chassis while the chassis

is powered on. The MXI-Express device may not be detected by the cDAQ chassis.

DIP Switches

The cDAQ chassis features six DIP switches, shown in Figure 1-1.

Table 1-7.

DIP Switches

Switch

Description

DISABLE
RT

(NI cDAQ-9138/9139 for LabVIEW Real-Time)

The position of the

DISABLE RT determines the operating system the cDAQ chassis boots
into. If the switch is in the OFF position, the chassis boots into LabVIEW
RT. Move the switch to the ON position to boot the cDAQ chassis from an
external drive.

(NI cDAQ-9138/9139 for Windows)

The position of the DISABLE RT

determines the operating system the cDAQ chassis boots into. If the switch
is the ON position, the chassis boots into Windows Embedded Standard 7
(WES7).

If the switch is in the OFF position, the chassis does not boot into Windows.

«
...
35
36
37
38
39
...
»

Содержание NI cDAQTM-9138














































































































































Отзывы:

Нет отзывов

Похожие инструкции для NI cDAQTM-9138

Бренд: Saitek Страницы: 44

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: Absima Страницы: 5

Бренд: JASTEC Страницы: 18

Бренд: Olsen Страницы: 4

Бренд: Acuity Controls Страницы: 5

Бренд: Risco Страницы: 232

CompleteStat-Series CS9B-THO

Бренд: Bard Страницы: 2

Бренд: EFI Страницы: 127

Бренд: maxxess Страницы: 11

Бренд: SOLARJACK Страницы: 14

Бренд: GE Страницы: 32

SYSVRF AHU 10HP S

Бренд: SystemAir Страницы: 16

Бренд: Zapi Страницы: 30

Бренд: Valcom Страницы: 9

Бренд: Espressif Systems Страницы: 11

Бренд: SainSmart Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды