National Instruments NI 9512 Скачать руководство пользователя страница 38

Страница: 38 / 44

ni.com

NI 9512 Operating Instructions and Specifications

Safety and Hazardous Location Standards

This product is designed to meet the requirements of the following

standards of safety for electrical equipment for measurement,
control, and laboratory use:
•

IEC 61010-1, EN 61010-1

•

UL 61010-1, CSA 61010-1

•

EN 60079-0:2012, EN 60079-15:2010

•

IEC 60079-0: Ed 6, IEC 60079-15; Ed 4

•

UL 60079-0; Ed 5, UL 60079-15; Ed 3

•

CSA 60079-0:2011, CSA 60079-15:2012

Note

For UL and other safety certifications, refer to the

product label or the

Online Product Certification

section.

Electromagnetic Compatibility

This product meets the requirements of the following EMC

standards for electrical equipment for measurement, control, and
laboratory use:
•

EN 61326-1 (IEC 61326-1): Class A emissions; Industrial
immunity

Содержание NI 9512













































Результаты поиска

Содержание NI 9512

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI 9512, Инструкция по эксплуатации и технические характеристики

Результаты поиска

Содержание NI 9512

Отзывы:

Бренды по названию

Популярные бренды