manualshive.com logo in svg
background image

Overview

This document explains how to connect to the NI-9472. In this document, the

NI-9472 with screw terminal, NI-9472 with spring terminal, and NI-9472 with DSUB

are referred to inclusively as the NI-9472.

Note

 Before you begin, read the NI-9472 Safety, Environmental, and

Regulatory Information document on 

ni.com/manuals

 and complete the

software and hardware installation procedures in your chassis

documentation.

Note

 The guidelines in this document are specific to the NI-9472. The

other components in the system might not meet the same safety ratings.

Refer to the documentation for each component in the system to

determine the safety and EMC ratings for the entire system.

Safety Guidelines

Caution

 Observe all instructions and cautions in the user documentation.

Using the product in a manner not specified can damage the product and

compromise the built-in safety protection.

Attention

 Suivez toutes les instructions et respectez toutes les mises

en garde de la documentation d'utilisation. L'utilisation du produit de

toute autre façon que celle spécifiée risque de l'endommager et de

compromettre la protection de sécurité intégrée.

NI-9472 with Screw Terminal and Spring Terminal Safety Voltages

Connect only voltages that are within the following limits.

Channel-to-COM

30 VDC maximum

© National Instruments

3

NI-9472 Getting Started

Содержание NI 9472















Отзывы: