background image

© 

National Instruments Corp.

5

NI 9426 Operating Instructions and Specifications

Special Conditions for Hazardous Locations Use in Europe

This eq

u

ipment has been eval

u

ated as Ex nA IIC T4 eq

u

ipment 

u

nder DEMKO Certificate No. 07 ATEX 0626664X. Each mod

u

le 

is marked 

 II 3G and is s

u

itable for 

u

se in Zone 2 hazardo

u

locations. If yo

u

 are 

u

sing the NI 9426 in Gas Gro

u

p IIC hazardo

u

locations or in ambient temperat

u

res of –40 °C 

 Ta 

 70 °C, yo

u

 

m

u

st 

u

se the device in an NI chassis that has been eval

u

ated as 

EEx nC IIC T4, Ex nA IIC T4, or Ex nL IIC T4 eq

u

ipment.

Special Conditions for Marine Applications

Some mod

u

les are Lloyd’s Register (LR) Type Approved for 

marine applications. To verify Lloyd’s Register certification, visit 

ni.com/certification

 and search for the LR certificate, or 

look for the Lloyd’s Register mark on the mod

u

le.

Caution

To meet radio freq

u

ency emission req

u

irements 

for marine applications, 

u

se shielded cables and install 

the system in a metal enclos

u

re. S

u

ppression ferrites 

m

u

st be installed on power s

u

pply inp

u

ts near power 

entries to mod

u

les and controllers. Power s

u

pply and 

mod

u

le cables m

u

st be separated on opposite sides of the 

enclos

u

re and m

u

st enter and exit thro

u

gh opposing 

enclos

u

re walls.

Содержание NI 9426





















Отзывы: