manualshive.com logo in svg

National Instruments NI 9251, Процедура калибровки, Страница: 2 / 8

Поделиться
Скачать
National Instruments NI 9251 Скачать руководство пользователя страница 2

NI cDAQ-9174/9178 USB Chassis Quick Start

NI-DAQmx installation and hardware setup

NI 9251 with mini XLR Getting Started Guide

NI 9251 with mini XLR connection information

NI 9251 with mini XLR Datasheet

NI 9251 with mini XLR circuitry and specifications

NI-DAQmx Readme

Operating system and application software support in NI-DAQmx

LabVIEW Help

LabVIEW programming concepts and reference information about NI-DAQmx VIs
and functions

NI-DAQmx C Reference Help

Reference information for NI-DAQmx C functions and NI-DAQmx C properties

NI-DAQmx .NET Help Support for Visual Studio

Reference information for NI-DAQmx .NET methods and NI-DAQmx .NET
properties, key concepts, and a C enum to .NET enum mapping table

Test Equipment

The following table lists the equipment recommended for the performance verification and
adjustment procedures. If the recommended equipment is not available, select a substitute
using the requirements listed.

Table 1. Recommended Equipment

Equipment

Recommended Model

Requirements

 

 

 

Calibrator

Fluke 5502A, Fluke 5522A,
Fluke 5530A

Use a high-precision voltage
source with gain error of
<100 ppm and offset error
<0.1 mV.

BNC (F) to Banana
Adapter

Pomona Electronics 1269

—

2

  | 

ni.com

  | 

NI 9251 Calibration Procedure

Содержание NI 9251









Отзывы:

Нет отзывов