National Instruments NI 9234E Скачать руководство пользователя | Manualshive

Страница: 8 / 31

background image

8

|

ni.com

|

NI 9234E Operating Instructions and Specifications

NI 9234E Circuitry

The NI 9234E analog input channels are referenced to chassis
ground through a 50

Ω

resistor. To minimize ground noise, make

sure the chassis ground is connected to earth ground. Each channel
is protected from overvoltages. The input signal on each channel is
buffered, conditioned, and then sampled by a 24-bit Delta-Sigma

ADC. You can configure each channel in software for AC or DC
coupling. For channels set to AC coupling, you can turn the IEPE
excitation current on or off. Refer to the software help for

information about configuring channels on the NI 9234E.

«
...
6
7
8
9
10
...
»

Содержание NI 9234E
































Отзывы:

Нет отзывов

Похожие инструкции для NI 9234E

Бренд: Samsung Страницы: 2

Бренд: OMA Страницы: 75

Pure Link 1300 Series

Бренд: lancer Страницы: 20

Бренд: Clarke Страницы: 8

Бренд: Reliable Страницы: 6

Бренд: Zepro Страницы: 64

Бренд: CAME Страницы: 28

4.3" Video Door Phone

Бренд: Alarmtec Страницы: 14

Terraneo 363211

Бренд: Bticino Страницы: 24

Бренд: Schake Страницы: 2

Бренд: Teac Страницы: 23

Бренд: LEXMAN Страницы: 28

Бренд: ENFORCER Страницы: 8

Бренд: hager Страницы: 6

Бренд: HADEF Страницы: 11

Бренд: Mi-Light Страницы: 5

Бренд: Kenwood Страницы: 160

Бренд: Kuzar Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды