manualshive.com logo in svg

National Instruments NI 9229, Руководство по эксплуатации

Поделиться
Скачать
National Instruments NI 9229 Скачать руководство пользователя страница 2

NI 9229/9239 

2

ni.com

This doc

u

ment describes how to 

u

se the National Instr

u

ments 9229 

and National Instr

u

ments 9239 and incl

u

des specifications and 

terminal assignments. In this doc

u

ment, the NI 9229 and NI 9239 

are referred to incl

u

sively as the NI 9229/9239. Visit 

ni.com/info

 and enter 

rd

s

oftwarever

s

ion

 to determine 

which software yo

u

 need for the mod

u

les yo

u

 are 

u

sing. For 

information abo

u

t installing, config

u

ring, and programming the 

system, refer to the system doc

u

mentation. Visit 

ni.com/info

 

and enter 

c

s

erie

s

doc

 for information abo

u

t C Series 

doc

u

mentation.

Note

The safety g

u

idelines and specifications in this 

doc

u

ment are specific to the NI 9229/9239. The other 

components in the system might not meet the same safety 
ratings and specifications. Refer to the doc

u

mentation for 

each component in the system to determine the safety 
ratings and specifications for the entire system. Visit 

ni.com/info

 and enter 

c

s

erie

s

doc

 for information 

abo

u

t C Series doc

u

mentation.

Содержание NI 9229



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды