National Instruments NI-9146 Скачать руководство пользователя

Страница: 26 / 29

Hazardous Locations

U.S. (UL)

Class I, Division 2, Groups A, B, C, D, T4; Class I, Zone 2, AEx nA IIC

Canada (C-UL)

Class I, Division 2, Groups A, B, C, D, T4; Class I, Zone 2, Ex nA IIC

Europe (ATEX) and

International (IECEx)

Ex nA IIC T4 Gc

Environmental

Temperature (IEC 60068-2-1 and IEC 60068-2-2)

Operating

-40 °C to 70 °C

Storage

-40 °C to 85 °C

Caution

Failure to follow the mounting instructions in the user manual

can cause temperature derating. Visit

ni.com/info

and enter Info Code

criomounting for more information about mounting configurations and

temperature derating.

Ingress protection

IP40

Operating humidity (IEC 60068-2-56)

10% RH to 90% RH, noncondensing

Storage humidity (IEC 60068-2-56)

5% RH to 95% RH, noncondensing

Pollution Degree (IEC 60664)

Maximum altitude

2,000 m

Indoor use only.

[1]

Shock and Vibration

To meet these specifications, you must panel mount the chassis and affix ferrules to

the ends of the terminal wires.

ni.com

NI-9146 Safety, Environmental, and Regulatory Information

Содержание NI-9146






























Результаты поиска

Содержание NI-9146

Отзывы:

Похожие инструкции для NI-9146

Бренды по названию

Популярные бренды

National Instruments NI-9146, Информация о безопасности, охране окружающей среды и нормативных требованиях

Результаты поиска

Содержание NI-9146

Отзывы:

Похожие инструкции для NI-9146

Бренды по названию

Популярные бренды