National Instruments NI 6612 Скачать руководство пользователя страница 46

Страница: 46 / 98

3-10

ni.com

Chapter 3

Counters

Other Settings

The counter measures the pulse using the Counter Timebase signal. By default, the counter uses
an onboard 100 MHz signal as the timebase. To change the timebase, use the CI.CtrTimebaseSrc
DAQmx Channel property.

You can filter noise on any PFI signal that is an input to the counter by enabling a filter. Refer
to the

PFI Filters

section in Chapter 4,

PFI

, for more information.

If you route the same PFI signal to multiple destinations, you should enable the Synchronization
feature. Refer to Chapter 4,

PFI

, for more information.

Semi-Period Measurement

Semi-Period measurements are very similar to pulse measurements. Refer to the

Pulse

Measurement

section for more information. In hardware, both measurements are the same;

however, data is returned with a different alignment.

In a Pulse measurement each pair of high and low times is returned as one point of data—each

point

of data consists of both the high time and low time. Figure 3-9 shows an example of Pulse

measurement.

In a Semi-Period measurement, the high and low times are returned as separate points.
Figure 3-12 shows an example of Semi-Period measurement.

Figure 3-12.

Semi-Period Measurement

Settings

The settings available for a Semi-Period measurement are similar to those available for pulse
measurements. Refer to the

Pulse Measurement

section for more information. For example, use

CI.SemiPeriod.Term to change the signal-to-measure.

Pulse measurements support sample clock timing; Semi-Period measurements do not.

rt T

ign

l to Me

asu

nter Time

bas

ffer

DAQmx Re

d V

e High

e Low

DAQmx Re

Содержание NI 6612



































































































Результаты поиска

Содержание NI 6612

Отзывы:

Похожие инструкции для NI 6612

Бренды по названию

Популярные бренды

National Instruments NI 6612, Руководство пользователя

Результаты поиска

Содержание NI 6612

Отзывы:

Похожие инструкции для NI 6612

Бренды по названию

Популярные бренды