National Instruments MXI-Express x1 Series Скачать руководство пользователя | Manualshive

Страница: 104 / 120

background image

D-2

|

ni.com

Appendix D

NI PCI-8366 Low-Profile Bracket Installation Instructions

5.

Remove the standard height bracket as shown in Figure D-2.

Figure D-2.

Removing Bracket

6.

Fit the low-profile bracket onto the NI PCI-8366 by aligning the square cutout on the
bracket with the SFP receptacle on the card. Ensure the two mounting tabs on the
low-profile bracket rest against the back side of the card. The mounting holes are aligned
with the threaded holes on the mounting tabs of the bracket, and the LED bulb is situated
in the bracket display hole correctly.

7.

Install the two Phillips screws from the front side of the card. Tighten each screw to a
maximum torque of 3.6 lb · in. (0.407 N · m).

8.

Hold the SFP module in the orientation shown in Figure D-1. Ensure the release lever is
closed in its upright position and gently slide the SFP module into the SFP receptacle. The
SFP module will click into place when fully engaged, as shown in Figure D-3.

Figure D-3.

Completed Low-Profile Bracket Installation on the NI PCI-8366

1

Standard Height Bracket

2

4-40 ×1/4 inch Phillips Head Screws (x2)

3

Front Side of Card

4

Mounting Tab

3

4

1

2

«
...
102
103
104
105
106
...
»

Содержание MXI-Express x1 Series

























































































































Отзывы:

Нет отзывов

Похожие инструкции для MXI-Express x1 Series

Бренд: ABB Страницы: 86

Бренд: Facnor Страницы: 33

Бренд: BARKO LOADERS Страницы: 85

Бренд: Mackie Страницы: 18

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 8

Бренд: Mackie Страницы: 7

Бренд: Mackie Страницы: 34

Бренд: Mackworth Страницы: 38

Бренд: P&P Страницы: 6

Бренд: Rath Страницы: 5

Бренд: Teac Страницы: 76

Бренд: Teac Страницы: 3

Бренд: Teac Страницы: 50

Бренд: Teagle Страницы: 2

Бренд: Qlight Страницы: 4

Бренд: Vision & Control Страницы: 32

Бренд: Axi Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды