National Instruments GPIB-VXI/C Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 226

background image

Chapter 3

Local Command Set

©

National Instruments Corporation

3-27

GPIB-VXI/C User Manual

Dynamic Reconfiguration Queries

These dynamic reconfiguration queries are described in the following sections:

•

Broadcast?

•

GrantDev?

•

RelSrvnt?

The dynamic reconfiguration commands are used to reconfigure the GPIB-VXI/C’s Servant
subtree after the system has entered the Normal Operation substate. If the GPIB-VXI/C is
RM, these commands can be used to reconfigure the entire system.

The

Broadcast?

query can be used to make the system or subtree enter the Configure

substate by broadcasting the

End Normal Operation

Word Serial query, or the

Clear

Word

Serial command followed by the

Abort Normal Operation

Word Serial query.

The

RelSrvnt?

and

GrantDev?

queries can then be used to restructure the

Commander/Servant hierarchy. You could perform dynamic reconfiguration directly by using
the

WSCmd

and

WSCmd?

local commands, but the GPIB-VXI/C’s RM table would not be

updated. By using the

RelSrvnt?

and

GrantDev?

queries to reconfigure the system,

you ensure that the GPIB-VXI/C’s system hierarchy and GPIB address link records do not
become corrupted.

You can return the system or subtree to the Normal Operation substate by using the

Broadcast?

query to broadcast the

Identify Commander

and

Begin Normal Operation

Word Serial commands.

«
...
67
68
69
70
71
...
»

Содержание GPIB-VXI/C



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GPIB-VXI/C

Бренд: Canon Страницы: 2

Бренд: XBOX Страницы: 2

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Jabra Страницы: 3

Бренд: Jabra Страницы: 4

Бренд: Vaillant Страницы: 52

Бренд: Vaillant Страницы: 11

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

FT-2000 - MENU MODE LIST

Бренд: Yaesu Страницы: 56

Бренд: Abov Страницы: 138

Бренд: Audioaccess Страницы: 2

U-verse Advance Series A10

Бренд: AT&T Страницы: 2

Бренд: Goodson Страницы: 4

Бренд: Moeller Страницы: 2

Бренд: Automated Logic Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды